We will be retiring the legacy profile avatars on. : New firmware version 1.6.1 is available for EOS-1DX Mark III : New firmware version 1.0.3.1 is available for EOS-C70 : New firmware version 1.0.1.1 is available for EOS R5 C : We are excited to announce that we have refreshed the ranking scale within the community! : Keep your Canon gear in optimal condition with a Canon Maintenance Service : New firmware version 1.0.3.1 is available for EOS-C300 Mark III : New firmware version 1.0.5.1 is available for EOS-C500 Mark II : New firmware version 1.0.3 is available for EOS M50 Mark II : New firmware version 1.3.2 is available for PowerShot G7 X Mark III : Service Notice:UPDATE: Canon Inkjet Printer continuous reboot loop or powering down : New firmware version 1.3.0 is available for PowerShot PICK : New firmware version 1.0.1 is available for CR-X300 : New firmware version 1.1.0 is available for EOS-R10 : New firmware version 1.1.0 is available for EOS-R7 : New firmware version 1.6.0 is available for EOS-R6 : New firmware version 1.6.0 is available for EOS-R5 : New firmware version 1.2.1 is available for EOS-R3 : New firmware version 1.2.0 is available for CR-N 500 : New firmware version 1.2.0 is available for CR-N 300 : New firmware version 1.1.1 is available for RF 70-200mm L IS USM : New firmware version 1.0.4.1 is available for EOS C70 : Help ensure your autofocus is properly aligned with a Canon Precision Alignment (Some sizes or types of paper can be loaded only one sheet at a time.) Select Rear Tray in Paper Source in the printer driver. ![]() Two or more sheets of the same size and type of paper can be loaded at a time so that you can print continuously. Printing 8.5x11 seems to work from the rear tray fine.Īny ideas on what's going on. You can load various sizes of paper, from 4' x 6' / 10 x 15 cm to A3+ (13' x 19') paper, in the Rear Tray. Printing over WIFI using IJ Canon network driver. I'm printing from Lightroom 7.3.1, on mac / high sierra with canon driver 16.20. I'd really like to use the rear tray due to space reasons. But when I go to print from the rear tray, it prints the image as if it were only 8.5"x11" (image is truncated). ![]() Second, If I set my paper size to 19W x 13H I can select the rear tray option. I can't leave the dialog without changing to manual feed. I get one of two errors:įirst, if I set my paper size to 13W x 19H and then go to the print settings dialog (Quality & Media tab) and I select the rear tray option, I get the following error message " A paper size that cannot be fed from Rear Tray was selected." It then tells me to select the "manual feed" option. If the disc tray guide (C) is open, be sure to close it.I'm trying to feed 13x19 paper into my printer from the rear tray (which is actually on top of the printer as opposed the the "manual feed" which is at the back).Open the paper support (A) of the manual feed tray, and pull it out. ![]() If you roll up this paper to flatten, this may cause cracks on the surface of the paper and reduce the print quality. When using Photo Paper Plus Semi-gloss SG-201, even if the sheet is curled, load one sheet at a time as it is.If paper is curled, hold the curled corners and gently bend them in the opposite direction until the paper becomes completely flat.įor details on how to flatten curled paper, see "Load the paper after correcting its curl." in Paper Is Smudged/Printed Surface Is Scratched. When printing on paper other than 14" x 17" (36 x 43 cm) size from a PictBridge compliant device, load paper in the rear tray. When printing on plain paper, load it in the rear tray. The manual feed tray does not accept plain paper.We recommend Canon genuine photo paper for printing photos.įor details on the Canon genuine paper, see Media Types You Can Use.
0 Comments
Leave a Reply. |